We have noticed this article involving Installing A Bathtub below on the internet and thought it made good sense to talk about it with you over here.
Mounting a tub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, and also often, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a reasonably challenging project. If the old bathtub is easily available, the project can relocate immediately; if you have to open a wall surface to eliminate the old bathtub as well as position the new bathtub, the job is much harder. In either case, the task is within a house handyman's skills, although you will certainly require a helper to vacate the old tub and embeded in the new one. Make sure you have actually qualified yourself for the job as well as are comfortable trying it. Rather than employing a contractor to take control of a halfway-completed project, it is far better to consider utilizing one before you begin. Possibilities are you may need a specialist plumber to make tube links.
This article will certainly assist you install a brand-new bathtub in your shower room if you have already acquired a new bathtub as well as do not need to transform the setup of your previous water system pipelines.
Your tools as well as material list ought to make up the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you should do is detach the supply of water. After doing so, activate the taps to drain any kind of water remaining in the system. The procedure of getting rid of the existing faucets can be quite troublesome as a result of the restricted accessibility that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly come from the pipelines. As soon as the supply pipelines have been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from turning during this process. When the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any old sealing compound.
Prior to carrying on to fit the brand-new faucets, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly require reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the installing opening in the bath/basin making sure that the washing machines are in place between the tap as well as the sink. Protect the faucet in position with the supplier provided backnut. Once the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with regular tap connectors. The previous kind should be connected to the tap ends first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Tub
Utilizing both wood boards under its feet, position the bathtub in the required position. The wooden boards are practical in equally spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the level as well as readjusting the feet on the bath tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable faucet adapter to the proper supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Switch on the supply of water and examine all joints and new pipework for leaks and tighten them if necessary. Fill up the tub as well as likewise inspect the overflow outlet and the normal outlet for leaks.
Finally, fix the bath paneling as explained in the producer's instruction manual. Tiling and securing around the bath tub must wait up until the tub has been made use of at the very least when as this will settle it into its last setting.
Getting ready for the Installation
Firstly, the sustaining structure supplied with the bath needs to be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to ensure that if the tap features a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to stop stress on the bathtub.
Fit the adaptable tap adapters to the bottom of the two taps making use of 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last position.
Tiling Around the Tub
In the location where the bath fulfills the tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split an inflexible seal, triggering the water to pass through the wall between the bathroom and the tiling, causing difficulties with dampness and also feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the bath tub with water prior to sealing, to enable the motion experienced when the bathtub is in usage. The sealer can crack relatively very early if you do not think about this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently readily available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very inquisitive about Tools You Need to Install a New Bathtub and I'm hoping you appreciated the entry. Don't hesitate to take the opportunity to distribute this content if you enjoyed it. Thanks a lot for your time invested reading it.
Services